翼型失速的非线性动力学特性及其控制

以NACA0012翼型为研究对象,应用CBS( Characteristic-Based Split)有限元方法对翼型绕流流场进行数值模拟,着重对翼型失速现象的动力学机理和特征进行研究.首先给出了静止翼型在不同迎角下流场的瞬时流线图以及静态翼型的迎角-升力系数关系曲线,并且分析出此曲线具有滞后、突跳等典型的非线性动力学...     

基于超高速碰撞仿真的卫星碰撞解体碎片分析

使用超高速碰撞数值仿真技术,结合自主开发的碎片识别统计方法,以Iridium33与Cosmos2251卫星在轨撞击解体事件为例,进行了在轨卫星碰撞解体碎片分析.通过有限元方法(FEM)与光滑粒子流体动力学(SPH)的复合算法,从图形角度识别出碎片云中的大碎片,然后利用二值图转换与二值图连通域的快速统计,提取出了碎片数目...     

Progressive prediction method for failure data with small sample size

The small sample prediction problem which commonly exists in reliability analysis was discussed with the progressive prediction method in this paper.The modeling and estimation procedure,as well as the...     

Control-oriented Modeling for Air-breathing Hypersonic Vehicle Using Parameterized Configuration Approach

This article presents a parameterized configuration modeling approach to develop a 6 degrees of freedom (DOF) rigid-body model for air-breathing hypersonic vehicle (AHV). The modeling process involves the parameterized configuration design, inviscous hypersonic aerodynamic force calculation and scramjet engine modeling. The parameters are designed for airframe-propulsion integration configuration, the aerodynamic force calculation is based on engineering experimental methods, and the engine model is acquired from gas dynamics and quasi-one dimensional combustor calculations. Multivariate fitting is used to obtain analytical equations for aerodynamic force and thrust. Furthermore, the fitting accuracy is evaluated by relative error (RE). Trim results show that the model can be applied to the investigation of control method for AHV during the cruise phase. The modeling process integrates several disciplines such as configuration design, aerodynamic calculation, scramjet modeling and control method. Therefore the modeling method makes it possible to conduct AHV aerodynamics/propulsion/control integration design.     

柔性扑翼气动结构耦合特性数值研究

微型扑翼体积小、重量轻,其柔性变形对气动特性有显著的影响。通过求解雷诺平均N-S方程(ReynoldsAveraged Navier-Stokes,RANS)和结构动力学方程,对微型柔性扑翼飞行器的气动结构耦合特性进行了数值模拟研究。针对微型扑翼的大幅运动,发展了适用于扑翼的气动结构耦合数值计算方法,研究了微型扑翼的气动结构耦合特性。通过求解雷诺平均Navier-Stokes(RANS)方程得到微型扑翼的非定常气动特性;利用哈密顿原理(Hamilton Principle)推导了扑翼的结构动力学方程,采用结构有限元方法对该动力学方程进行离散并求解,得到扑翼的动态结构特性;采用松耦合方法进行迭代。计算结果与风洞实验结果相比吻合良好,验证了所发展方法的有效性。在此基础上研究了惯性力和关键运动参数对柔性扑翼气动及结构特性的影响规律,有助于比较详细、全面地了解微型扑翼的气动机理,为柔性扑翼的设计提供了参考依据。     

直升机的气动弹性问题

直升机的气动弹性问题与固定翼飞机不同,不仅要考虑单片桨叶,更要将旋翼视为一个整体,考虑其动态入流、尾迹影响以及旋翼与机身之间的相互耦合等。就单片桨叶而言,在结构动力学上,需要考虑离心力场、几何非线性以及桨叶的非线性挥舞-摆振-扭转耦合;在气动力上,需要考虑动态入流以及桨尖处可能的失速效应,本质上属于非线性气动弹性力学范畴。由于旋翼气动力通常是以周期形式通过旋翼轴传给机身,并引起机身振动,而机身运动又通过改变桨叶根部形态反过来影响旋翼的气动弹性特性,这种旋翼/机身耦合问题,也是近年来直升机气动弹性问题研究中的重要方向和热点之一。此外,随着旋翼流场数值分析方法的日趋成熟,采用动态重叠网格或滑移网格方法来实现桨叶运动,并通过动网格技术来实现桨叶的弹性变形,从而实现弹性旋翼流场的数值模拟,目前正呈现出勃勃生机,成为直升机气动弹性研究的又一重要方向和热点。随着各种新构型直升机的相继出现,如倾转旋翼机、前行桨叶概念旋翼(ABC)直升机和复合式直升机等,也带来了新的气动弹性问题。不断发现问题、解决问题,推动本学科持续发展,永远是气动弹性工作者终身奋斗的目标。     

一种温度动态调节方法及其动态性能仿真研究

航空气源模拟试验台主要用于模拟不同飞行状态时发动机给空气管理系统的供气,由于飞机爬升、降落时发动机供气参数会急剧变化,因此航空气源模拟试验台需具备动态能力.基于一种温度动态调节方法,在合理简化的基础之上采用NHT方法对其温度动态性能进行了仿真研究,仿真结果表明该温度动态调节方法能够满足温度动态性能需求,对动态航空气源模拟试验台的设计选型有较高的参考价值.     

考虑非理想噪声干扰的直升机飞行动力学模型辨识方法

利用MATLAB/SIMULINK平台搭建了直升机仿真实验系统，并以UH-60直升机为对象实现了考虑非理想噪声干扰的仿真飞行实验。建立了非理想噪声数学模型并基于增广最小二乘法设计 了一套同时考虑模型参数和噪声参数的综合辨识算法，在此基础上，利用仿真实验数据实现了UH-60直升机纵向飞行动力学模型的辨识与验证。最后，通过与普通最小二乘法的对比验证了本文方法的优越性。      

Hexapod多自由度微激励系统的振动时域波形控制

摘要： Hexapod多自由度微激励系统常用于航天器有效载荷在轨微振动环境的模拟，但采用现有控制方法无法精确稳定跟踪低频正弦加速度，这是由于系统耦合度高、非线性在低频段较强，被控对象相位滞后过大造成的.针对此问题，基于传统离线迭代控制方法，提出一种复合超前校正、多倍频陷波滤波器的改进离线迭代控制方法.其中，离线迭代进行补偿控制，超前校正进一步补偿系统相位，多倍频陷波滤波器去除非线性干扰.跟踪低频定频正弦加速度的实验结果表明，对比传统离线迭代控制方法，改进方法收敛快、控制精度高；对比现有自适应正弦振动控制方法，改进方法将符合精度要求的加速度控制频带下限由14.5 Hz扩宽至8 Hz.实验结果验证了所提方法的有效性.     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.